I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am using the Evaluation Kit, and I have tried to send some data between the Developoment Dongle (PCA10000) to the Evaluation Kit board (PCA10001). As the Development...
Hi,
Are there any reference design for interfacing a nRF51822 with an external sensor for e.g. an accelerometer (STM LIS3DH, AD ADXL362 etc)
Also do we have a profile...
My application would like to receieve notifications at several different times before a radio notification event. Specifically the application needs to receive notification...
Hello,
i have two operation modes:
One or more devices are bonded and advertising mode with whitelist (BLE_GAP_ADV_FP_FILTER_CONNREQ)
A new proximity central device...
Hi all,
From this forum and the examples given in the "sdk" find two approaches to measuring the battery voltage:
using external divider 10M/2.2M+22nF
using integrated...
In the previous discussion you told me to buy Mod nRF-8001 from olimex and i was also very optimist after going through its design that it can easily be connected to Arduino...
I have an application in which I would like to be able to enable and disable the SoftDevice.
But there are peripherals (Application Timers, Two Wire Interface, etc) that...
Hi,
I'm using PCA10001 connect to a sensor chip.I would like to set the register values for sensor chip as SPI master role and I need to switch to slave role to read the...
Hello,
i just want setup 1Tx and 1 RX using NRF24L01+ chips. but i am confused what should be Transmitter side Tx & Rx and what should be in Rx Tx & RX ? in order to use...
Hi,
There were similar questions already anwsered but none of them work for me. So the situation is as follows. When i program the chip though SWD interface the chip probably...
Hi,
Regarding the source found in "Nordic/Source/ble*" etc (downloaded as part of the nrf518xx SDK
[*] How can I find out which revision/release-tag I'm using. Would...
My design may not connect to a client for most of its operational life but will need to be in advertizing mode whenever not connected. I want to specifiy the advertizing interval...
The nRF Utility app for Android does not support the Galaxy Note 3 yet. Probably because the phone has only been released for a few days so far.
Please add support for...
Hi all,
I am a new user to the BLE technology and to the Nordic's development tools/chips.
I use the nRF51822 development kit and the nRFgo Starter kit to develop a BLE...
In my current project, I have to develop a board with 2 mcu:
nRF51822
STM32F2/F4
The nRF51822 should running S110 SoftDevice and act as a kind of »over the air«...
