I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
I try SDK hid mouse example this days, In SDK v4.2.2 it does not work sometimes when I press button 0~3 ,and some times the mouse arrow move slowly when I press the button...
Hi,
I'm trying to make the nRF module work with an older IO demo board. Does the flexible GPIO system via pin crossbar allow you to modify the pin assignments of the SWDIO...
I what to send button data , how to construct button data array :
uint8_t buffer[INPUT_REP_BUTTONS_LEN]; in function ble_hids_inp_rep_send() ?
In SDK mouse demo I can...
I want to add to lbs service battery service(bas) as well. One of the changes is in the advertising_init() function:
static void advertising_init(void)
{
uint32_t...
Hi,
We have a custom board, with accelerometer sensor, our ultimate aim is to collect the accelerometer data and transfer it to the master device (PC or smartphone) using...
Hi there,
Will any 4.1 features by making their way into the respective Soft Devices any time soon?
I would imagine 32-bit UUIDs would create some memory pressure on...
I am trying to use Eclipse+GCC for my projects. I found a similar issue as stated in the following post:
devzone.nordicsemi.com/.../nan-29-nrf51-sdk-no-project-files
...
I am having trouble getting up and running with the development kit (without the starter kit).
My setup is as follows:
The PCB antenna module is hooked up to the JTAG...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
When the Ant stack want to transmit a packet while the BLE stack is using the radio, an event called EVENT_CHANNEL _COLLISION will be returned, is that...
Hello,
when the device NRF8001 starts Advertise, it sends out only one packet and unexpectedly terminates with a fatal hardware error in "ll_ctrl.s0.c" line 572. This happens...
Hi,
I'm trying to install Master Control Panel v.3.5.0 on Win7 64bit but I get the "Master Control Panel Setup Wizard Ended Prematurely" message. I have .NET Framework...
It would be very convenient to increase the output power of nRF51422/822/922 with at least 3-6 dB in order to get enough range. I'm currently not using nRF51422 for ANT, only...
with 1.16.0.3031 I cannot recover but I still can recover in Linux using a tweaked Makefile.posix
I don't remember this problem with previous version. Hence it must be...
I have tried to configure the nRF24A2 chipset in the asynchronous transmission mode by setting the bits in the extended field assignment. Unfortunately for some reason, it...
