Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
members.efn.org/.../main.c works fine but members.efn.org/.../main.c.pwm seems to break the softdevice. The big difference in my mind is that there is a Timer2 interrupt...
Hi all,
I have developed so far on dev board (mbed) and I am moving to my own board now.
After some trouble getting the blank device programmed I have problems running...
I'm just getting started with the nRF51 Eval Kit, I have the 5.1 SDK installed, using Mac OS X for development. I also have the GCC ARM toolchain installed. Firstly, I had...
Folks,
I have the S110_SoftDevice_Specification v1.1 (great doc, thanks) and the doxygen-generated API docs. But is there an App Note or other document that fills the void...
Description of my system:
Hardware:nRF51822, pca10001
Software: SDK5.20, S120
If i first call the function ble_stack_init(); and then i open the LFCLK first by set...
Hi,
I'm working with the heart rate demo for the nRF51822 Development Kit and I can only connect and discover with the development dongle and master control panel. If I...
Hi,
I use ble_app_uart project (pca10001) and new softdevice7.
I find a DFU project at nrf6310 directory of SDK .
when i program both projects the uart application...
I am aware of L2CAP API exposed by the SoftDevice SDK sd_ble_l2cap_cid_register(...)
How can I find out if this API will create a connection-oriented and dedicated channel...
Hello!
I would like to use the nRF51822 and build a pcb design in Eagle. While i tried to create a new package i couldn't find any specification for the qfn-48 6x6 the...
1.description of my system:
Hardware:nrf51822,pca10001
Software:sdk5.20,run the softdevice s120
2.the problem i meet,in the main() function
the first i called the function...
Hi,
We are using nRF51822 BLE device in our product. As we got to know that this chip cannot be factory programmed.
Can you please suggest us how we can program this...
Does the following flasher also allow to debug the nRF51822 device?
Segger Flasher Portable
If not... which flasher/debugger is suitable to be used during development...
I'm adding the bond manager to an existing nRF51822 s110 soft device project to enable encryption when reading/writing certain characteristics of a BLE service.
As far...