Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
I have seen this forum post: devzone.nordicsemi.com/.../
Which refers to this blog post: devzone.nordicsemi.com/.../
But when I use the Keil Packs Installer, and check...
Hi,
I'm approaching the nRF51 tools for the first time and I'm trying to recompile the source code for the desktop 2 reference kit with Keil 5.14 as a sanity check for...
I am developing an application where a repeater unit connects to a number of other units, gets some info, aggregates it and broadcasts it as a peripheral unit (in a tree structure...
20150424_iPad_iOS(8.1.3)NrdkKS_sniffer.psd
Dear Nordic,
I want to control the volume up feature through HID for iOS while pressing the key.
How can I proceed for...
Greetings,
I have a peripheral (S110) , when it is connecting to a central, it also need to scan another broadcaster (beacon) to obtain its RSSI and send to the central...
I have adopted the S120/S110 multilink example to the following: central.zip and peripheral main.c
I want to send a notification from the central to the peripheral and...
I've developed an application on the nRF51 DK, now for further testing purposes I need to upload it to the nRF Beacon (PCA20006).
My software uses SDK8 (S11 v8) and it...
I want to get rid of the board support package, and write my own code to interface with the least complicated drivers for UART, BLE and SPI etc.
If I remove BSP I ifind...
hi i have pca 10001 eval kit .I need to connect it with PIC16L1947 controller via uart.The data transmitted from pic is to be collected by nrf51822 and it should send as advertisement...
I am developing an application from scratch for the pca10001 by copying a lot of code from the heart rate example.
When calling "softdevice_ble_evt_handler_set" I get an...
I am looking over the stack-up for the dev board which I received from an FAE and has designed in a 50mil width PCB antenna. I am using this online calculator here:
emclab...
Hello--
The nRF51-Dongle has these 20 pads which I think correspond to a debug port:
On the schematic, it looks like these feed into JTAG signals:
My question...
Hello,
I just got a nRF51 DK and I'm trying the examples of nRF folder in the Pack distribution (SDK 7.2).
I can compile the Blinky project but its not working if I...
i have the nRF51DK that comes with the Segger j-link programmer. Can i use the programmer on the board to program a custom board i purchased from Nordic preferred vendor?...
