Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, and thanks for reading this.
I attached additional LED to nRF51822 p0.24
however I can not find how to handle it .
if I want to use this function
nrf_gpio_pin_set...
Hey.
Hope this was not asked before. At least I did not find it.
I'm trying the ble_app_hrs_c on s120. Got it to build with gcc (d'oh) and got the serial logging to...
I want to make a robot that can track the direction of the transmitter that is controlling it, for example to aim a camera at the transmitter. The robot vehicle will be controlled...
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi!
Maybe I'm doing something wrong (very possible), but for example, when I want to store array of 3 uint8_t values I use:
uint8_t dataToStore[3];
dataToStore[0] ...
Device: nRF51822 Rev G0
SDK: v5.2.0
Code: raw.githubusercontent.com/.../twi_hw_master.c
Basically, the TWI driver which uses PPI channels (sd_ppi_*) works perfectly...
Hello,
I am using a nrf51422 development kit with softdevice S310 and I have a problem in whatever pin I choose as output when I use the bluetooth.
I run the example...
I tried code like
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
....
case BLE_GAP_EVT_TIMEOUT:
if (p_ble_evt->evt.gap_evt.params.timeout.src == BLE_GAP_TIMEOUT_SRC_ADVERTISEMENT...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am unable to compile this to fit into the allocated bootloader space.
Has anyone been able to compile this patched version of the signlebankdfu-ble
with nrf sdk v6 so...
I'm using API 2.1.3, and after several connections/disconnections with a peer device, I'm seeing the API never returning from a DiscoverPipes() call. It appears to be waiting...
Hi,
I'm using nrf51 BLE driver with usb dongle to create test application on PC which simulates
the peripheral.
My problem is I cannot add 128-bit UUID for custom service...
After some pstorage_update calls I start to get error 9. From nrf_error.h it is called NRF_ERROR_INVALID_LENGTH but from SDK doc it looks like pstorage_update does not have...
