Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, I am creating a PCB design and am not sure if I should connect the pad under the nRF24L01+ to the ground plane with a couple of vias.
The data sheet says it should...
Is there a plan to support the BLE central role in the software stack?
As it is now, I absolutely cannot use the nRF51822 since the S110 stack does not support operating...
The attached test program and logic analyzer displays shows that the function twi_master_transfer() returns to the calling program before the transfer is complete, if TWI_hw_master...
The error I get is app_error_handler 0xDEADBEEF, 360 (line number), src\ll_lm.s0.c
This is with SD 5.2.1
With SD 6.0.0.1-alpha, sometimes I get
app_error_handler...
Does anybody know of any plans to combine the Peripheral and Central roles into a single SoftDevice?
The killer application that this provides is the ability to create...
Hi All,
I use nrf51822 transfer data to nrf uart app for android,when I use following parameter ,the device and nrf uart app work well.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS...
I'm interested in advertising with data type 0x18 random target address. I found a post for advertising with 0xFF manufacturer specific data. What changes are necessary for...
Hi,
I am using bluez 5.12 and am having difficulty connecting to an nRF51822 EK running the Health Thermometer application and Soft Device S110v6.
I am able to see the...
Hello,
I cannot build a known-buildable project and get error A1023E.
No Programmer's Reference exists and there is no documentation referencing this error.
I think...
I want to quickly transfer data between nRF51822 and celluar phone. The data rate is 100 packets/sec. Packet size is 14 bytes. We know mouse can reach almost 200Hz report...
can i use j-link debug probes to program and debug evaluation kit?
recently i bought J-Link debugger from the segger, i tried to find the pinout of the SWD of the eval...
I see that the source code of app_gpiote.c uses NVIC_... functions to handle the interrupts:
app_gpiote_init.c, line 160...:
NVIC_ClearPendingIRQ(GPIOTE_IRQn);
NVIC_SetPriority...
My question is regarding the adertising with the softdevice on the heart rate sensor example.
My starting point is the following:
I connect PCA10001 / PCA10000 from...
Hi,
we are interested in the combination of the nRF51822 with a sensor board which was announced in October but since then there were no updates and I can not find any other...
Hi
We know most of access contol for entrance was implmented by RFID. Is it feasible to design it by BT4.0? My idea is as below. Thanks for your comment.
There is a...
