Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
We need to sense temperatures in the upper end of the operating range, specifically in the 40C to 70C realm. We have three different units, and we are finding that the temp...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
I am currently working on interfacing an external flash memory IC (Winbond W25FV series) with the Nordic nRF52832 on my custom board , using the nRF Connect SDK .
However...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hello,
we are testing software with the nRF54L15 DK with the 3.0.2 SDK and toolchain.
When creating a board configuration we use:
nrf54l15dk/nrf54l15/cpuapp
optimize...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
