I have created the nRF Cloud Multiservice Sample application and would like to add WIFI support.
I am using nRF9151 with nRF7002 EK hardware and would like help in adding...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
Hi,
I am currently trying to integrate a digital microphone with the I2S peripheral of nRF5340 audio DK. I am accessing the P10 header of the nRF board for the particular...
Hi,
I need to enable an input interrupt on nRF52832 and I want to use a GPIOTE EVENTS_IN channel.
During boot configuration, I'm using nrfx_gpiote_in_init function with...
Hello Nordic Support Team,
I have three queries to make.
Is it possible to force the channel in which the data transmission is happening using nRF52840 DK.
To explain...
Hello,
we are testing software with the nRF54L15 DK with the 3.0.2 SDK and toolchain.
When creating a board configuration we use:
nrf54l15dk/nrf54l15/cpuapp
optimize...
Hello!
I'm taking some performance metrics for encrypting data on my nRF52840 device and I was wondering if you might be able to help me. The goal is to see how long and...
I'm getting the following warning on my terminal during build:
-- Including generated dts.cmake file: D:/Workspaces/azure_iot_hub_9/build_pmi/mcuboot/zephyr/dts.cmake CMake...
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
Hello DevZone,
I have learned that some knowledge about CLOCK. But they are a little bit confusing. I just want to get confirmed by any expert.
1. Some peripherals ...
Hello,
I am looking to create my own custom NRF5340 AUDIO DK board. Could you point me to any NRF5340 modules that would be best to use with a pre-built antenna, available...
NRF52840DK NCS 2.8.0 Hello , We are developing an application where a device with router function must join a coordinator network. The coordinator uses OOB (proprietary IR...
I am working with the WLCSP version part (nRF54L15-CAAA) and it calls out that there is light sensitivity. The note seems to indicate that only underfill around the perimeter...
how to upload modem firmware and and connect to nrf cloud and send modem firmware and asset tracker hex file and procedure to connect to nrf cloud ( i tried and sim activated...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I get the source code from the github.com/.../ncs-fund.git , and trying to build the exercise-1-5 of nrf-connect-sdk-fundamenta lesson-4-serial-communication-uart for 54l15dk...
Hello,
I attempted to follow the nrfutil offline install instructions. However, I keep receiving the following error when trying to install the device package on the remote...
I solved this but the solution wasn't obvious and it didn't show up on google so I'm going to leave a quick writeup here.
nRF Connect SDK 1.7.1 on windows and linux
We...
nRF52832-QFAA using the LDO power supply mode，The firmware is configured to operate in the LDO power supply mode.The compilation and download processes are all fine.but the...
Hello,
i am currently trying to build a minimal firmware for the nRF5340 on the Thingy:91x. Unfortunately my build failles to link zephyr/zephyr_pre0.elf:
My suspicion...
