Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hi all,
Actually I'm building with vscode my firmware for a custom board build with an nRF9151 non secure. After building I got a merged.hex file, this is the file upload...
Hello i am running the radio_test sample on the custom nrf5340 board for the logging purpose i am using the pins 8 and 9 of the port 0 but the issue arising is that there...
Hi.
I made the smallest system module using nRF52840. The schematic diagram is as follows.
My reference design for power supply is as follows,
For Firmware....
I have a 5 year old design using a nrf52832 on a MDBT42Q module. The BLE option was placed on the PCB in 2020 and has been unoccupied since going into production. My customer...
Hi Noridc expert ,
I am trying to configure using nsib + mcuboot on nrf52840,
I need to build the image with only public key avaliable , and sign the image else where...
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
We are developing a project that runs BLE, the Nordic Uart Service, the Nordic Distance Measurement toolikt and Async UART (NCS v2.9.0). The Peripheral device shall advertise...
Hallo,
we are using the nrf5340 and the ncs Version 2.6.1.
I activated the software downgrade protection as described here Downgrade protection (nordicsemi.com) .
Then...
I just received a new 54L15DK and was attempting to port a simple 5340 project to it. The first time I attempted to flash it, it _looked_ like it was successful:
[1 0/10...
In our application we using nrd5340-nrf7002, application flow is wakeup->wifi connect->NTP time get->TCP server connect->wifi shutdown->idle->wakeup..... We are encountering...
Hi Nordic
I am curious how to test nRF54L15 BLE sensitivity and Blocking.
I am currently using:
1) nRF Connect For Desktop" v5.1.0
2) Direct Test Mode v2.4.0
...
Hi y'all.
I've been developing in Zephyr NRF52840. My code is based in Central_HR_Coded (SDK 2.6.1, Toolchain 2.7.0). I had some issues with the bt_conn_disconnect function...
Hi, I'm new to this product and currently working on the Nordic Thingy:91X and have encountered some issues that I need help with. below is the details from the serial
monitor...
Hi,
I am developing an application with LTE-M connectivity to nRF Cloud. Our previous SIM apparently supported auto-APN provisioning, we did not have to set the APN, the...
Hello,
I bought brand new Thingy53, but Thingy53 turn off during deployment and can not connect to BLE, becuase it turns off. Please assist me if possible.
Hi,
I test my nrf54l15 module(disconnect every gpio with outside),the sleep current was 3uA,seens can't not achieve 0.6uA as the datasheet said.
The nrf54L15's markcode...
I am experimenting with sampling IQ at the payload in AoD mode. Are there any differences in the configuration of the receiver in AoA mode as seen in the direction finding...
Dear DevZone,
I believe I am quite familiar to this forum due to my ongoing Wi-Fi issues with SDK 2.6.1 To determine if a newer SDK version will resolve these problems,...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...