I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
It is indicated on page 59 of the datasheet (rev1.0), concerning the register nr.8 OBSERVE_TX, that "the counter PLOS_CNT is reset by writing to RF_CH . See page 75...
I am working with SDK12.2.0. I see that transports seem to be registered as section variables with the identifier dfu_trans
I have added a section definition in flash to...
Not sure if this is a typo in the function comments or a small bug, but thought you'd probably want to address it either way. I'm on the most recent NRF5-SDK (12.2.0) and...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Gentlemen,
I'm trying to develop a Health profile solution that works with Win 8.1
I'm using SDK 6.0 and S110 v 7
Win 8.1
I found the Win 8.1 sample app...
I am looking at the Master Emulator examples ProximityDemo and HealthThermoDemo. I can use both to connect to one device that I have (Device A). I try to use ProximityDemo...
Hi,
I want to achieve DFU OTA nRF51 using NRF52832.Is it any example,or data transfer message sequence charts documentation? Could you give me some suggestions?
Thanks...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi,
I hope you are doing well. I am working on nrf51822 project. I want the nrf51822 to advertise for 5 secs and then sleep for say 30 mins or an hour and then wake up...
hello,
Starting nRF 52832 (s 132), leaving idle, after 3 minutes, ble_event_id 0x1b will occur, then BLE communication will be impossible.
When ble_event_id is 0x1b, how...
Hello,
I'm having special SPI protocol which requires SPI Slave to toggle REDAY pin after every byte. I do test using 2 nRF52 boards. One is SPI master, another is slave...
Hello all, first time using a I am using a nordic board im a little overwhelmed by all the options. I have nrf51 development kit and I just used the getting started tutorial...
I'm starting a new design on nRF52 and I need to connect a microphone on it. Reading the datasheets and questions here, I found there's 3 solutions for the type of microphone...
Hi,
I was reading the procedure to prepare the NRF52 DK board for current measuring and some questions came into my mind. I understand we have to open the P22 so we interrupt...
