Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
Hey there!
I'm trying to run the 'wifi/shell' sample on v3.0.1 on a nrf7002dk (targeting the nrf7002dk/nrf5340/cpuapp) with sysbuild enabled, of course and I'm getting...
Hi Teams
I am designing a product using the 9151 SIP. According to the specifications, the operating voltage ranges from 3 to 5V. From the hardware design guide, I learned...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
We have a design in EVT and we're preparing for FCC testing. It's a dual radio board with nRF52840 and a Semtech LR1110. Therefore, we need both to be active and transmitting...
Hello,
we are developing a device which implements BLE hid keyboard. The code is based on the hid keyboard example in the NRF Connect SDK.
The example uses battery service...
Hi Nordic team!
Is there any way to dynamically change the charging current while the charging is ongoing? BCHGISETMSB and BCHGISETLSB can be changed only if charging is...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
Hello,
We have an nrf522840 board using retained memory feature following this sample and using the NRF_RETENTION setting:
https://github.com/zephyrproject-rtos/zephyr...
Hi,
My project is based on NRF52832 with SDK11.
I got 2 working units, 1 is advertiser and 1 central.
The advertiser is advertising every 2 second.
The central unit...
Hi all,
We've followed the reference EVK designs closely and are now in the Pre-Production phase.
The initial development board was intentionally large to accommodate...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
Hi,
I am getting framing error notifications from the nrfx uarte driver on a zephyr platform when receiving data from a certain external device, but only when there are...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
