Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
I am trying to implement LittleFS on 1Gb QSPI NOR flash (W25Q01JV) on the nRF5340.
I am running nRF Connect SDK version 2.4.2 and am using a slightly modified version of...
Hello. I am using nrf52832 for Ble-based positioning. currently i am tackling with establishment of an anchor measuring rssi values and sending them to a central center (a...
Hi,
I am trying to run the nRF91x1: DECT NR+ Shell example on my nRF9161 SDK board.
I get this crash when the code runs
Can you point me to the explanation of what...
We're building a prototype board which uses the nRF52833 and want to tune the RF components. The radio_test sample in SDK 3.0.0 doesn't seem to support the nRF52833 SoC. Is...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
It seems the "reset" button on my nrf52840dk doesn't do anything anymore. I believe this started happening after I enabled mcuboot in sysbuild. Is this expected?
When we were using nrfjprog to flash, we used "west flash --erase" because it was quicker to erase entire flash then sector by sector. However, when we upgraded to SDK 3.0...
I am using nRF54L15 with Zephyr to measure voltage with ADC. In the struct adc_sequence there is a calibrate bool, but I am not sure what it does. What is the reference that...
Hi,
Does Central or Peripheral UART enable ACK/NACK in the code for BLE communication? How does Peripheral recognize if Central has received all the data ? Is there any...
nRF52832, SDK17.1, s132 I work with SPI and it works on the this project with SDK15. But I have transferred this prj to the SDK17.1 and I can't make SPI work. I don't get...
We have a product which is based on nrf52840 and nrf connect sdk 2.8.0
After OTA sometimes, I find that the NVS is erased, which could lead to some issues on client side...
Hello, I am working on a project using zephyr as well as the nrf5340 MCU. For this test, I am on the nrf5340dk. My application requires I drive a PWM at 125khz. In my device...
I opened up the nRF Connect for Desktop application and noticed a new version for the SDK , 3.0.0. I also noticed that the application is being deprecated.
Inside of Visual...
