Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
I have my development board nrf52 PcA10036 and I am trying to run a ble basic example. I started using the blinking program and it works without problem, therefore i got full...
Is it possible to manufacture a RFID tag that works within the 2.4GHz wifi wavelength range allowing a mobile-phone to power and pick up data from this RFID tag. Data would...
I have a application which can enable and disable the softdevice.
I need the softdevice only to send some informations, after the sending the stack will be disabled.
...
I have a Nordic micro-controller nRF51 with 128kb of flash memory, I compiled with Keil, I generated a a program with:
Program Size: Code=23856 RO-data=632 RW-data=308...
I want to enable Notifications in my Central for a particular characteristic advertised by my Peripheral. There's example code that is supposed to do this in the BLE Central...
Hello,
i have a question about the use of the dc/dc converter in use with the softdevice S310 v3.0.
We make some difficult calculations and so the sensor its on for 750ms...
hi
as we know,ANCS need to pair,we have app for ios,iphone will pair with our devcie when i connect my device by my app,so iphone will connect my device when user open...
hi
my customer want to add DFU funcation to their APP(ios and android),i give them nrf toolbox source code ,i hope they can separate DFU funcation from that source code...
In my application I have to advertise and scan, I know these two actions are multiplexed and there are no problems when there is no BLE connection (I use s130, sdk 9.0.0)...
Hi all,
I'm developing little project on nrf51 dongle(pca10031). After few succeses now I have big failure which stops my work.
How my environment looks like: Ubuntu...
I built the GCC bootloader from source based on the suggestion of another user in this forum instead of using a precompiled hex file. The Softdevice is 7.1.
It shows DfuTarg...
I have a min connection interval of 200ms and max of 250ms. I have set slave latency to 10. These parameters are set both on peripheral and on central. Still, after connecting...
Hi! I am working on a project that uses the Multilink example. On the client (nRF51422 w. SD 120) my program crashes and starts the main loop again after a few seconds. I...
Hi,
I'm developing a device that will be powered by two AAA alkaline batteries.
Since the operating voltage of nRF51822 is 1.8 to 3.6V I was considering to connect them...
