Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I use nrfgo studio to program the hex file. but I have only 128kb of flash and the softdevice took 88kb which left less then 50kb. I have a hex file of 70kb
my question is...
hello.
I develope the using the Nrf51822, bootloader and application not using softdevice llbrary.
the procedure is that one mcu send the mrf51822 by uart. and mrf51822...
Now I have generated bootloader.hex used by /DFU/bootloader.
After programming bootloader.hex and s110_nrf51_8.0.0.hex,the device's name changed to DfuTarg.
But when I...
Hell,
Wich BT dongle I can use to dawnload data fro board with nRF51822 chip on it?
If thear is App. to use for comunication and dawnloading data from electronic board with...
Hi,
I am using nRF51422 with s130 soft device along with SDK v9.0. I am trying to read/write flash memory using pstorage module. I am using BLE nus service for data transfer...
each time I start my program (nrf51 device) I get an error code I save in flash to check it at next restart. I can read error code 0x20
is this a correct error code and what...
Hi,
I try to generate a PWM signal on PCA10040 with the nRF52832. To do that I copied the code from the Product Specification into my application, but nothing comes out....
Hi,
I made my prototype board using the nrf51822 chip. for this prototype i use an on-board connector + external programmer to flash the nrf51822 chip.
that's work...
I am looking ahead to the time when I will graduate from using the nRF52 development board to building a custom device with the SoC. The PCA10036 chip will obviously not be...
Hello,
I am almost finishing developement of a BLE module using nrf51822.
For mass production, I hope I can program Softdevice/Bootloader/Firmware to 10 nrf51822 using...
Hi
I want to receive and send a lot of data in a short time (connection Intervall is set to 20ms). And I get the App-Error 0x3004.
I found this definition for the error...
Hello,
I am currently trying to figure out a problem with my mesh. If I stop the event handling of one node, other nodes in the network will fail to send data from this...
PAN #9 in the nRF51822-PAN-v2.4 document provides a workaround for non-functional OUTINIT. This question and this one improve the workaround and state it's unnecessary in...
We have used the first version of the S132 softdevice with the Engineering A version of the nrf52 chip. Now with the newer Engineering B version, we have moved to the second...
