Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi DevZone Engineers,
As I am unable to access my board (Xiao BLE Sense (embedded form) with Nordic 52840 SoC) through the "Connected Devices" tab in nRF Connect, I am trying...
Hello!
I'm new to Nordic Semiconductor and currently developing a project for which I need support regarding the nRF9151 DK . Before placing an order, I would like some...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
Hi,
I’m facing an issue with RTT logging on my nRF52840 using NCS 2.6.0. I’m trying to log output from the B0 bootloader, but so far, I’m only able to capture logs from...
Hi, I am trying to set my acqtime different to the max value. And the build throws an error unless i set it to ACQTIME_MAX.
It appears in the header file it needs some other...
Hi,
We are currently in the research and development phase for a new line of IoT devices designed to work over the Matter protocol. After thorough evaluation, we found the...
Hello,
I'm trying to run the BLE LTE sample following this guide on an nRF9160 DK. I get the following error:
[00:00:04.942,413] <inf> nrf_cloud_info: Modem FW: mfw_nrf9160_1...
We are in the process of integrating the Nordic nRF Mesh SDK version 3.3.3 into our Java-based application.
The devices we are working with are pre-configured BLE mesh devices...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
Hello,
I am currently working on integrating the ENC28J60 Ethernet module using SEGGER Embedded Studio and nRF5 SDK version 15.0. As part of this project, I would like...
Hello,
We have a fresh install of SDK 3.0.1 (from within VS Code), toolchain 3.0.0. We try to follow the Matter adding cluster tutorial ( https://docs.nordicsemi.com/bundle...
