Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello, My SDK is NCS2.8.0, I want to know the version of matter, but I can't find it, may I know how to get?
BTW, does NCS SDK support Matter 1.4.0, if yes, could you tell...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used. Logs are having corruption.
Looks...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
Hi,
I'm planning to use the nrF51822 in the end product and the nRF51DK kit has nRF51422 and not the nRF51822. the user guide for the kit says that 51422 supports ANT protocol...
I am doing a bootloader to support updates via ESB. I am using MicroLib. I am not using SoftDevice.
My project mapping:
Bootloader 0x0000-0xBFF
Application Vector Table...
I use Keil uVision 4.74.0.22 to compile nRF51-ble-bcast-mesh-master with nrf51_sdk_v6_1_0_b2ec2e6 and get the rbc_mesh_BLE_Gateway.hex. However, I drag and drop the hex file...
The iOS app we have is identifying the device via the name broadcasted and the service UUID. On production devices, are the Service UUIDs on the same product, the same on...
Fisrt of all, I have searched all the questions but now still can't make bond work.
I've done below work:
1, modify main.c file to add device manger function
2, modify...
Hello,
I am using NUS service as a peripheral with read and write characteristics and tested on master control panel.
Now I am using S120 stack for central device and...
Hi,
I have a PCA10028 which has a 51422, and trying to run ble_app_uart_c example on it. But no success. I don't get any thing on COM and LEDs do not turn on at all. Does...
Good morning,
I am using nRF51 SDK v10.0.0 and I have to synchronize access to a hardware resource shared between two control flows. One flow is an interrupt handler invoked...
I just ported my SDK 9.0 app timer code to SDK 10.0 which requires the use of the new APP_TIMER_DEF() macro. The problem is that is generates warnings in Keil (v5.17) that...
I am using nRF51822. I want to know that how to perform file read, delete and write operations. Is there any API available for this. If file operations are not supported by...
We are trying to integrate an accelerator driver with the code written in c++ with example code from twi sensor from the SDK 0.10 for the nRF51, which is written in c. Will...
Hi,
I am struck with the problem of GAT ERROR when I upload my application zip file through Nordic nRD ToolBox in Android.
These are my steps:
I load the S310...
I recently migrate to SDK 10 from SDK 9 and printf is behaving weird with baud rate of 92100 (460800 and below works fine). Some of the characters were printed out of order...
Hi,
I am trying to implement some custom services in PCA10028 version 1.1.0 with Android, I am following same code which is in github ( github.com/NordicSemiconductor) it...
