Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hello Forum,
I have purchased an nRF52 Preview Development Kit and has successfully tested the blinky and the Hart Rate Simulator.
The document "Product Brief" from Nordic...
Hi,
I am trying BLE multilink central example from SDK9 on PCA10028 board, but everytime device gets stuck at LEDS_CONFIGURE() in main.c.
Below is my setup:
Flash...
Is there any way to stream the BLE data from nrf52 preview development kit to a PC/MAC? I saw this app devzone.nordicsemi.com/.../ but it doesnt work with nrf52.
Can anyone...
just i want to connect PC by normal BLE dongle.
i am using window8.1. and my nrf51822 chip using
ble_app_uart... i can communicate with smart phone but
on my PC, just i...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,all. i use ble sniffer to capture data between my phone and device,that sniffer says:malformed packed and connect failure.What's wrong?
连接不上问题抓包01.png
Hi
I've noticed that the Generic Attribute Service in profile code developed with S110 is missing the READ property on the Service Changed characteristic. It has INDICATE...
Hi, I want to logg faults on my system so in the app_error_handler I want to store some data to flash. This location in flash is erased earlier when no error was present so...
Hi,
I would like to know the time it takes to send the three advertising messages in one advertising period (on channel 37,38,39). What is it? How do I measure it?
Can anyone post this file, or a link to it? I don't have Keil(using GCC with Eclipse) so I appear to be unable to intall the pack that contains this. I am trying to get the...
I want to use timer0 to get exact time delay (without soft device used).
Timer0 configuration is as
void timer0_initialization(void)
{
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;...
Hi,
At present time I perform many tests with power level and link stability. And noticed that if cover nRF base device with hand or put into pocket the disconnection with...
Hello,
Is there any way to configure the flash data default values during programming phase with Keil IDE?
In IAR, it is possible using a file ".s43" included in the...
Hello, I'm using the nRF51822_QFAA chip on a custom board, but the layout and parts are the same as on the nRF51822 USB dongle . I tried flashing the Board\pca10001\s110\ble_app_hrs...
I am using nRF8001 with EMF32.
inside hal_aci_tl_send function
C : 1, 14,
inside hal_aci_tl_event_get function
E : 3, 132, 128, 130,
It is looks like
Length == 3
...
