Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
Hi,
We have an extra current of 1uA while in system off mode(no RAMS). we get ~1.6uA instead of 0.6uA as we read on SPEC.
Do you have an idea what may cause the extra 1uA...
I am trying to modify the ble_app_hrs so that i can write a value to the board and save it as a new heart rate value. So far i have added a BLE_GATTS_EVT_WRITE case to the...
Hi,
I tried my best to solve my problem via forum but unfortunately no success.
I got nrf51 DK and played with it a lot. successfully program the samples and tweak them...
Per release notes, flash memory footprint has changed. The Multilink central project resets when trying to clear pstorage memory area and so I'm assuming that it is protected...
Hi,
Since i don't have nrf6310 board, i tried to test the multilink central application with pca10001 board, after referring the nRF51 SDK document. But unfortunately it...
Folks,
I've designed and implemented two product prototypes using the QFN package for the nRF51822. Now I need to move to the BGA version to shrink the designs. The nRF51822...
Im using the nRF51822 board with the nrfGo motherboard. I noticed the atmel microcontroler on the motherboard supports USB otg. It is possible for the nRF51822 to use the...
Hello,
I just received my nrf51822-mkit. I would like to connect it to android, but I need the product keys. I cannot find the product keys on the PCB or in the packaging...
Only p0.00 to p0.03 event can trigger an interupt in nrf 51822?
By nRF51 Series Reference Manual v1.0 ,I find that it only have CONFIG[n] (n=0..3) in GPIOTE, does it means...
Hello.
I use nrf51822 EK and TN-901 temp sensor.
My plan is nrf51822 slave, TN-901 is master
or considering the roles reverse.
Getting value is spi and output is uart...
s120 1.0.0.1-alpha loads fine
s120 1.0.0.2-alpha won't load - The given hex file did not load successfully
s120 1.0.0.3-alpha won't load - same error message
See attached...
Folks,
Prototyping a wearable device using the nRF51822, so we're talking about Bluetooth LE and the 2.4 GHz band (although the protocol probably doesn't matter). Since...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
