Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
We are evaluating the Thingy:91x and found that the BLE range is significantly decreased compared to the Thingy:91. The nRF5340 has a lower maximum TX power but when...
Hi,
1.How should nRF21540 be added to the nRF52840 DK ncp example? Please provide the lines of code that need to be modified. 2. How should the uart interface be modified...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hi,
I have a question about creating a custom board. I am following the tutorial here: youtube
I am trying to make a custom board for nRF54L15 using the board wizard ...
Hi,
A few months ago, I raised a ticket regarding the integration of SoftSIM into the nrf_cloud_multi_service sample. With the help of one of your support engineers, I was...
Hi,
I'm trying to play some sounds on a piezo with the help of the pwm. I tried to set the period with pwm_set_dt but only the first call is successful and every subsequent...
Hello everyone
I need help. I have a custom board that uses the nRF5340 microcontroller. I am using the Zephyr OS and nRF Connect SDK Toolchain v2.9.0. How do I update my...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hi, not exactly a problem rather it is question on whether this setup is suited for what I want,
I want 3.3V for the device and sensor systems, possibility of reducing...
Hi All, I have a question regarding modem DECT phy API. There is a function nrf_modem_dect_phy_event_handler_set(nrf_modem_dect_phy_event_handler_t handler). I'd like to know...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
nRF52832 custom board + NCS 3.0.1
We are using the Zephyr driver for LIS2DH sensor in "any motion" detection mode, which triggers an interrupt when acceleration exceeds...
