Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hello everyone,
Could anyone tell me which pins are the programming pins of the nRF51822 chip for a QFN48 packet ? How can I program it on my custom PCB?
thanks..
We are planning to use nRF52 for its superior computing power in an application. Unfortunately it appears that the throughput is more limited than on nRF51. Since we need...
Hi,
I used two 51822 modules for my project. One should send a byte and other one should receive.
I used the exact same configurations of radio examples (transmitter and...
I am trying to read an analog value on the GPIO port into my application. Looking through the examples, there aren't any that help solve this problem as the ADC example is...
I have tried to follow the installation instructions and have installed nRFGoStudio, the Keil MDK-ARM, and downloaded the latest nRF52 SDK. I also installed all of the device...
Hello,
Iam a beginner to NRF51 and Iot.
I want to be able to send messages from raspberry pie to NRF51 dk and vice versa via Bluetooth.
Iam using a generic Bluetooth dongle...
Hi ,
I've just started using a Nordic's product : an nRF51 422 QFAC develepement Kit
I was running tests by loading examples on this board when I lost the connection between...
I am building my application up on the blinky free rtos. I want to use RTC and ble stack. i am initialising RTC1 first and ble stack stact.
The problem is that I am getting...
I am using nordic nrf8002 BLE with a breakout board & not a developement kit. I gave 3.3v supply in different combinations:
(1)3.3v to vdd pin-1, GND to vss pin-4
(2)3.3v...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
How can I calculate the maximum throughput for an application running on the nRF51822 and the S110, when connecting to different kind of Central devices?
If we want to obtain sets of five "Bluetooth stylish temperature sensors, do you have a selling point in The Netherlands? If not maybe a way to obtain this by mail or parcel...
