Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi,
I use the nrf52 dk(PCA10040). When monitoring the current consumption of the advertising with the DCDC enabled, we see some current spikes. Why?
Here is two screenshot...
I modified the code of ant_background_scanning_s212_pca10040 to make it works with s310 on nRF5144 xxaa.
The code works fine, but loose a lot of RX packets (more than 80...
Bluetooth device directional broadcast (set my mobile phone Bluetooth device address), I open the phone Bluetooth, will automatically link if you can not automatically connect...
Hi,
The samples for using list are BUFFER = 4, but it does not specify is that is the only size that works, and what value do you place on NRF_SPIM0->TXD.LIST
In my...
Here is a little background.
I have been developing a product based on the S130. I used the device manager from the S120 device since version 0.9 alpha. I was able to build...
Is there a mechanism to notify the application when a client reads from an attribute? For example, I have a large attribute buffer (100 bytes max) with a default MTU size...
Hi,
We are implementing a device where we need to use BLE and PWM. For generating PWM we use app_pwm library. To decide on the number of cycles of PWM pulses, we use a separate...
Hi,
Is there a way to power only the nrf52832 on the development kit(PCA10040)?
Background: We would like to test a solar power source but we don't want to power the...
Thank you very much in advance for any help.
I am attempting to upload an example firmware on a nRF52832 with the s132 softdevice BLE stack and the example DFU bootloader...
just like
github.com/.../nrf52-mpu-easydma-using-timers-and-drivers
we add a sensor, and try to read 2 sensors by 3 command in i2c.
is it possible to still using ppi...
Hi Friends,
I am beginner for nRF51822 and I install uVision 5.20 to create program for this chip.I can't see this chip on device selection table when new project creating...
Hi,
I've recently bricked my nrF51822 Beacon Kit ( www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit)
...by uploading some bad firmware. I can no longer program...
I am beginner for nRF51822.I installed uVision 5.20 to program nRF51822 chip.I could not see nRF51822 chip on chip selection guide of uVision software.Also I need some example...
Hello.
I've been trying to use the nRF Beacon for Eddystone app to configure a nRF52 devkit. The idea is to configure a slot as EID and register it to my google account...
Hi there,
I know 3V lithium batteries (Lithium Manganese Dioxide) batteries would be perfect for the nRF51822, but we're wondering if Lithium Thionyl Chloride (Li-SOCl2...