Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Im tring to generate sbom in html or spdx format yousing west ncs-sbom -d build i got this error: package.name += '-' + package.version TypeError: unsupported operand type...
Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hello everyone,
I'm developing an application using the SX128x radio with the LoRaWAN Basic Modem.
The project runs successfully on a custom board based on the nRF5340...
Hi Nordic Team,
We are using the MIMXRT1050-EVK as the host and the nRF7002EK as the Wi-Fi module with an SPI connection. However, we are encountering frequent errors that...
Hi,
SDK: 3.0., nRF54L15
The application is Matter + BLE dynamic multi-protocol + battery powered sleepy end device. Current Application(Matter/Thread + BLE + Firmware...
I’m using the Zephyr nordic,npm1300-charger driver on an nRF52840 to control the nPM1300 PMIC charger. At runtime I need to be able to turn charging on and off—on command...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with two specific exercises: l2_e3 and l4_e1 . Other...
Hello, I can commission bulb and switch pass, then I refer this link( acl and bind ) to write ACL and binding both, eventually I can use switch to control bulb!
But I have...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hi,
I need to implement low power mode in my project with an nRF52832. From a general perspective, I want to:
1) boot the device,
2) initialise stuff/peripherals,
...
Hi,
I am analyzing the issue that the BLE module can maintain a relatively short connection distance. Besides the transmission power and frequency offset, I also take...
Hello, guys, I am working on direction finding using nRF5340 DKs and v.2.9.0 SDK. I found that an antenna array is required to find the direction using nRF5340 DKs. So is...
I use nRF5SDK1230, S130nrf51201. Firstly, I flash ble_app_beacon in PCA10028, it works good. then i flash the same program in custom board(nrf51822qfaa) without any change...
Hi Nordic team, 您好，北欧团队，
I am developing nrf54L05 in VS code with NCS.I want to configure the SEGGER_RTT_printf to my project.Is it correct to change the CMakeLists.txt...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
hi, any SMBus support on the nRF54L or nRF54H?
many recent charger + (in-pack) pcm/gauge-IC's talk directly to each other, while this being smbus 3.0/3.1, utilizing notify...
I have built and flashed the openthread/coprocessor sample using VS Code specifying "nrf54l15dk/nrf54l15/cpuapp".
I then tried to run it (on Ubuntu 24.04.2 LTS, x86_64)...
