Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi:
for nRF51
I want to send command to link manager by HCI command ,or example LMP_test_control, LMP_Activate , etc. Could I modify firmware to do it ?
thanks;
All...
Hello,
I have an issue that I can't seem to sort out involving the PWM module. I am currently using SDK9.0 and SoftDevice S110 V8.0 and I am using the stock PWM files from...
I have a nRF51DK. And I would like to be able, to enable/disable the softdevice with 2 buttons.
Button 1 on nRF51DK --> Enable Softdevice
Button 2 on nRF51DK --> Disable...
Hello,
I am working on nRF51822 S110 softdevice 8.0 and SDK9.0. I am creating paired and unpaired states and the system will goto unpaired only if it is unpaired from the...
I know nrf51 timer0 can be configured for 16,8,24 and 32 bit modes
and timer1 and timer2 can be configured for 16 and 8 bit modes.
But what can I expect the value to be...
I'm going to star a new product development using nRF51422 supplied by a 3V battery. Since it is a low cost product the idea is to use the nRF51422 internal DCDC to provide...
Hello,
I'm using an external chip that decodes my RF transmission and outputs the data on two pins DAT, and CLK (data and clock). Currently I'm reading the data with GPIOTE...
We have written our own softdevice, but now we have a question about the stack pointer.
I read in the softdevice specification that the nordic softdevices share the stack...
I have been trying to establish a link that will feed sensor data into my com port via a Bluetooth uart bridge. I got my closest today by doing the following.
Load SDK10...
I'm having trouble making a single bank dfu mode with 128k NRF51822 chip.
Here's the problem;
Works fine when everything(SoftDevice, Application, Bootloader) is all...
Hi,
I am a newbie to Nordic BLE.
A make error occurs when building the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0 on my cross compile environment...
Good morning, i have windows 7 and at this moment i have installed "Gnu tools for ARM embedded Processors", "GnuWin32 ‐ GNU Make utility", "GnuWin32 ‐ Core Utility", "nrfgostudio...
Hello,
on our custom hardware design, the hardware reset won`t be executed after programming with nrfjprog.exe, until complete new boot with disconnecting Vcc.
After reconnecting...
