Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
When I call sd_ble_gatts_sys_attr_set and p_sys_attr_data points to data in flash I get a NRF_ERROR_INVALID_DATA. When I point to the same data in RAM I don't get an...
I am using NRF_TIMER1 with 16-bit mode and prescaler of 0 as a counter, to count the pulses of an incoming square wave signal in a given time window. What is the upper limit...
Hi Nordic,
Can you please shed some light on the size of NFC stack on nRF52?
Also, what NFC operation modes (Reader/Writer, Peer-to-Peer, Card Emulation) can be supported...
I'm pretty new to embedded systems development, but I've started to find my way around. I am trying to strip the SDK example programs down to minimal examples, in order to...
Hi!
I am trying to implement oob pairing, but I don't know how to do it.
I' ve got 2 nrf devices. Central and peripheral.
Central receives oob data, which it stores in...
Hello, I am using spi_master example to get a sensor output from ADXL345. Currently, it seems my code can read output data, but there is error showing for settings mismatch...
Hello!
I successfully followed nAN-36 and loaded the code into a NRF51 DK (PCA10028).
The next step I intend to take is to prepare a custom central service that matches...
Why sd_ble_gattc_hv_confirm returns NRF_ERROR_BUSY ?
I want to send a confirmation after I receive a indication from server(s110 ) ,when I receive data ,
in on_evt_hvx(...
I am trying to figure how to pin my nrf51822 on a PCB. I need the chip to sample and convert an analog voltage signal coming from a photodiode heartbeat detection circuit...
Hello
I want to setting up DFU in my project. I followed this document :
link text
I'm using IAR EWARM and nRF51_SDK_8.0.0 and "nRF51_SDK_8.0.0\examples\dfu\bootloader...
Dear all,
I have written some code that controls the SPIS and allows it to transfer data as if it were a master. I am generating the SPIS clock from one timer, and I am...
Hi everyone
for my application I must use the Bluegiga dongle like central (PC side) and nRF51822 for peripheral (hardware side).
So I implemented cable replacement app...
I feel stupid asking this question, it should be documented in the standard and the code but I have looked and googled with no luck.
I want to populate the ble_rscs_meas_t...
