Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello guys!
I have a strange problem where the nrf9151dk suddenly won't power up. It was working fine - I was only working with SW, not HW.
I got a pop-up error saying...
Hi Noridic team,
I have enabled Matter over Thread on the nRF5340. In this setup, I'm planning to reduce the TX power by setting CONFIG_OPENTHREAD_DEFAULT_TX_POWER=0. Apart...
Hi,
I have a question about FOTA jobs with queued and failed devices.
Let's say I am managing a group of 10 cellular devices (nRF9151) through the nRF Cloud UI. I create...
Good day,
I am currently working on a project involving the nRF54 series and would like to inquire about support for the NEC infrared (IR) communication protocol. Specifically...
I'm testing my code based on nrf5SDK v17.0.0 with nrf52832 board.
By nrf connect application,I can see the broadcast packet from my board.It looks something like this. ...
Hi I'm working with nrf5340 dk. I have a serial app (on windows) that is doing serial write continuously to the nrf5340 dk but it is not capturing all the data that I'm sending...
Context
We are working on a project that implies advertising and scanning extended advertised packets.
details :
NRF52840
Zephyr SDK 17.0
Zephyr 4.0.99
NRF SDK...
I am trying to port code I developed on the NRF52 DK to a MDBT42Q-512KV2 BLE module from Raytac I purchased from Digikey and am running into problems.
I developed all the...
Hello,
I'm working with a custom board, using an nRF5340 (NCS v2.7.0 but also tested with version 2.9.0) and a W5500. I'm trying to run the DHCPv4 client test just to verify...
Dear Nordic company,
I have question connected with nrf9151 chip. I know, that this chip contains two parts, ARM core and modem.
I am trying to understand of Serial...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Hi,
The nRF Connect Extension on my Windows VS code doesn't load altogether:
I uninstalled VS code - including all it's settings/extensions etc using this post's suggestion...
Hi,
I can build and program the broadcast_source sample application using the Python script:
This runs fine and broadcasts as expected. However, I cannot get the application...
Hi, I'm working with the nRF9151DK and Zephyr RTOS (v3.7.99 / NCS 2.9.1) . I’ve configured UART1 to send and receive data via GPIO pins:
TX: pin 8 (P0.08)
RX:...
