Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
I'm now studying about Gazell.I'd like to get Gazell specification which describe about its packet format,network topology,and so on.
Moreover,does the nRF51822's Nordic...
Hi all,
i am having issues with the mKit and current consumption.
Just an FYI to measure consumption i am placing the mKIT in series with a shunt resistor and measuring...
I've spend some time figuring out where the application code should start for the S130 . Table 11 in the SoftDevice Specification v0.5 document indicates that it is at 0x00020000...
I check the function spec that we can use use 32kHz RC as LFCLK, so I have no external 32k crystal connected with XL1/XL2 on my board.
I have set
NRF_CLOCK->LFCLKSRC =...
Hi,all:
I have a question.
could I use android/ios APP to connect several BLE devices at the same time?
because I want to use andriod APP to control all of the BLE...
I'm trying to write a central BLE with the dongle(PCA1000) using s120.
I programmed s120 sd ver 1.0 the same way as the s110 with the nrFGO ver 1.17.
However i keep getting...
Hi all,
I need to change the device name frequently to show button status.
So remote device can see button status without connecting to device.
Is there any way to...
Hi guys,
i have a service with more characteristics and more states. Not every characteristic should be available in each state. Thus there are services which are just...
Using the S120 soft-device in the Central role, there does not appear to be an
example or documentation describing how to scan for a 128 bit UUID service.
Has anyone tried...
Apparently there is some limitation on length of the paths with Keil. The paths are specified under "Options for Target" --> C/C++ --> "Include Paths". Due to this limitation...
I downloaded the nrfgo Sdk for the nrf24lu and nrf24le. In the projects folder there are several examples, two of which are of interest. The first is entitled "bootloader_32K...
Hi
I'm having a strange behaviour when using the TWI HW peripheral for reading from an I2C device. My application tries to read one byte from a register in a I2C device...
Hi,
I'm done with the hardware interface of my current project.
Right now I have a service running with a custom UUID, by writting this characterisitics you have access...
Hi,
I'm having the purpose to use nRF51422 /ANT to connect a relatively data hungry ANT device. The nRf51422 specs expose three programmatically available data rates : 250...
