Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi,
MPSL radio notification API has been removed from the nRF Connect SDK v2.6.0.
Is there any alternative way to get radio notifications?
Regards,
Narendra
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
We are developing a project that runs BLE, the Nordic Uart Service, the Nordic Distance Measurement toolikt and Async UART (NCS v2.9.0). The Peripheral device shall advertise...
Hallo,
we are using the nrf5340 and the ncs Version 2.6.1.
I activated the software downgrade protection as described here Downgrade protection (nordicsemi.com) .
Then...
I just received a new 54L15DK and was attempting to port a simple 5340 project to it. The first time I attempted to flash it, it _looked_ like it was successful:
[1 0/10...
In our application we using nrd5340-nrf7002, application flow is wakeup->wifi connect->NTP time get->TCP server connect->wifi shutdown->idle->wakeup..... We are encountering...
Hi Nordic
I am curious how to test nRF54L15 BLE sensitivity and Blocking.
I am currently using:
1) nRF Connect For Desktop" v5.1.0
2) Direct Test Mode v2.4.0
...
Hi y'all.
I've been developing in Zephyr NRF52840. My code is based in Central_HR_Coded (SDK 2.6.1, Toolchain 2.7.0). I had some issues with the bt_conn_disconnect function...
Hi, I'm new to this product and currently working on the Nordic Thingy:91X and have encountered some issues that I need help with. below is the details from the serial
monitor...
Hi,
I am developing an application with LTE-M connectivity to nRF Cloud. Our previous SIM apparently supported auto-APN provisioning, we did not have to set the APN, the...
Hello,
I bought brand new Thingy53, but Thingy53 turn off during deployment and can not connect to BLE, becuase it turns off. Please assist me if possible.
Hi,
I test my nrf54l15 module(disconnect every gpio with outside),the sleep current was 3uA,seens can't not achieve 0.6uA as the datasheet said.
The nrf54L15's markcode...
I am experimenting with sampling IQ at the payload in AoD mode. Are there any differences in the configuration of the receiver in AoA mode as seen in the direction finding...
Dear DevZone,
I believe I am quite familiar to this forum due to my ongoing Wi-Fi issues with SDK 2.6.1 To determine if a newer SDK version will resolve these problems,...
