Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
I am trying to populate a nrf_twi_mngr_transfer_t at runtime depending on chunks of an input file that I'm pushing to i2c.
nrf_twi_mngr_transfer_t const write_cfg_transfers...
Morning, I was trying to access https://academy.nordicsemi.com/ but the browser responded with an error `Domain configuration pending` and showed `Kinsta` node is down. Any...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
Hi,
I am desperate with creating my own board. I followed the example of nrf54l15dk, but I absolutely do not understand why I cannot build - not even assembling Zephyr....
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hello! One of our projects will have nRF52832 replaced in EMS with revision 3 silicone and we wonder if description in is valid. It states that:
In factory state, the [new...
Dear Nordic-Support,
I have registered handlers for the two voltage level thresholds with the nrf modem library using modem_battery_low_level_handler_set and modem_battery_pofwarn_handler_set...
Hi Nordic Team,
I am working on implementing synchronized sensor sampling on multiple Bluetooth devices that are externally triggered. To achieve this, I have combined the...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
I have recently bought two nrf52840dk, version 3.0.0, unboxed and plugged into usb. One would show up with a usb storage on the side and in vscode a J-link window prompted...
Hi,
I am getting framing error notifications from the nrfx uarte driver on a zephyr platform when receiving data from a certain external device, but only when there are...
