When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Background : To set up a Matter ICD (Internet Connectivity Device) and Thread as a SSD (Sleepy End Device). Here are the detailed settings：
Currently, the Matter over...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
We are currently working on a custom modem firmware update. For this, we would like to use the CBO file you provided. Updating the segments with the CBO file is working so...
***Description***
I am trying to build a sample application which comprises of a notification from peripheral to central. I configured the PHY to 2M. With the mentioned...
I am trying to use Health SRV and Health CLI to check if there are any errors in the nodes. I have successfully transmitted the fault codes, but there are still many questions...
I have a battery operated unit & according to the data sheet I should be able to read the VDD pin
However, when I look in the nrf-saadc.h it does not have this listed...
Hi Nordic Team
We are developing products using the NORDIC NRF54L series chips, but we are encountering some hardware issues.
We have used the NRF52832-QFAA chip. Packaged...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
I am trying to make a simple MAC-layer transceiver using Arduino environment. I have some code derived from this example: https://github.com/IoTS-P/nRF52-802154-Raw-Transmitter...
