Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards. I want to check my runtime. So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Hello all.
I am now making a central device to control a peripheral device.
The Firmware of central device is supposed to be updated by Smart Phone, like iOS or Android...
I'm currently making a device which use nRF52832 and that will integrate Capacitive touch feature. However, I'm actually a bit lost with this post: devzone.nordicsemi.com...
Hi, I use PCA10040 v1.1, Keil MDK 5.21a, SDK 12.1 with S132 v3.
I was using SDK 12 previously. The SDK 12 projects worked well.
Now I migrating to the new SDK. So...
Hi all, I'm working on SDK11.0.0 with softdevice S130 v2.0.0 and I need to update bootloader+application at the same time in single zip for these I created zip file by using...
I have a use for the pstorage module and while going over the implementations in the Nordic examples and libraries, I found a use-case of pstorage_register() in bootloader_init...
Hello,
I would like to use the PCA10028 close to the conditions of a future custom board at 1.8 V (including I/Os) but I would like to keep the ability to do source level...
I am using the 8.1.1 version of the SDK on a Rigado BMD-200 device, s110 version of SoftDevice.
The code has set APP_ADV_TIMEOUT_IN_SECONDS to the maximum (all bits set...
My main App must be able to use the soft device directly or serialisation when a external Connectivity chip is used. How can this be done? In the examples it's done at compilation...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards.
I want to check my runtime.
So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Looking at the nRF51 UART Example, i know that all packets transmitted over a BLE link will be protected by CRC on the link layer.
But how about when nRF51 scan the ibeacon...
Hi, I would like to use RTC1-> cc[1] using app_timer drivers. How to do this? Examples show only the usage of RTC1->cc[0]. RTC1->cc[0] has been used by ble_conn_params.c and...
Hi,
After few hours my program is crashing and I'm landing on address 0x1AFF4 which belongs to softdevice. For what is responsible this code and what could be a reason...
