Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi, I need help for generating the init packet. I'm using SDK 11.0.0 , s130 on nrf51822. To build bootloader, I've used the sample bootloader with some include path changes...
I try to print the RSSI level but i couldn't do.
I use nRF51 DK and soft device S130.
This is the line that i just write:
SEGGER_RTT_printf("RSSI: %d\n",p_gap_evt-...
I'm trying to create a project from scratch that can use the S132 Softdevice, but I am constantly running into problems trying to get the correct headers, preprocessor macros...
Hello Nordic,
I am using the BL600 third-party module and SDK 10.
I was able to modify and compile project with GCC at
examples\ble_peripheral\ble_app_uart\ for s110...
As title,
I found that on the official website,
and I think it's extremely useful for someone(me) who need to measure the power consumption(current).
I can't find...
When I operate RESET PIN in main function like this:NRF_POWER->RESET = 1,Then cause a HardFault_Handler, (/attachment/fabd1141d36157d32f8c0353e4880b3e),What's this？
hi NORDIC,
is it possible to store float array in fds. i am able to store intrger values but unable to store float values. i am using example in this link :- github.com...
We have observed in couple of large size deployments that data packets from beacons that are bit far away tend to be corrupted. Devices that scan the signals from BLE beacons...
I have read the previous questions regarding the above subject, i found that changing the maximum bonding devices limit defined in device_manager_cnfg.h will work, but it...
Hello everyone, I must to write and read a I2C eeprom like 24c256. I tryed to do it but all the examples with I2C protocol works with 8bit addressing. I tryed to modify mpu6050...
Does the components on the development kit increase the power consumption compared to what you would expect from a low power-optimized application-specific PCB?
Other than...
I use the ble uart app to receive the data from mobile phone. The data packet size is 20 byte. If I transmit the packet one by one without adding delay, is it possible that...
HI,
Can anybody give me the connections to a BMD-300 with nRF52DK and the steps to program a BMD-300 from scratch? Which document provides the information, if there is any...
For ble_app_uart, if I write below routine to send data to mobile phone application. Can the mobile phone application receive all the packets without packet lose.
for(i...
