Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
There are two NUS services here, but only the second one can send data through the RX characteristic. I've checked the source code and nothing has changed. How do I delete...
I have created the nRF Cloud Multiservice Sample application and would like to add WIFI support.
I am using nRF9151 with nRF7002 EK hardware and would like help in adding...
I'm using Zephyr/NCS v2.7.0 with a custom multi-image project based on sysbuild . My top-level project has a sysbuild.conf at the root, and a sysbuild/ folder containing a...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hello Nordic Support Team,
I have three queries to make.
Is it possible to force the channel in which the data transmission is happening using nRF52840 DK.
To explain...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hello, we are trying to use the distance measurement module and we are following the sample code from sdv v3.0.2. The build process for nrf5340dk and nrf52840dk works well...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hi,Team,
I'm currently using the nrf54l15-dk. I want to set the rtc of the nrf54l15-dk to obtain the timestamp. How should I configure the rtc? Which examples should I refer...
I'm working on an nRF device (S112 SoftDevice) that acts as a connectable peripheral to an iOs central. The application only has data to transfer every 5 minutes, so I'm trying...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
