Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I am currently working on a two way communication between an nrf52840 thread host and an nrf52840 thread client over coap. I have nrf connect sdk version 2.9.0 in both...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hello Nordic team, We are trying to use ST7305 display (custom driver that we have developed using st7789V as refrence ) and acconeer A121 senors on same SPI bus. The A121...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Dear Nordic Semiconductor Team, I hope this message finds you well. I am currently developing a project called Nuntius Core, which involves controlling bait boats (carp fishing...
Hello,
I am currently working with the nRF5340DK and the W5500 shield. Both work perfectly when using the dhcpv4_client application. However, when I attempt to use the recv...
Howdy!
We have designed a custom PCB using the BC840 from Fanstel. We have been able to connect to and program both the BC840 evaluation board (EV-BC840-V0) and the custom...
I am unable to debug a Fanstel BM840 nRF52840 based simple custom board using a nRF52840 DK. I believe the custom board is basically ok: Before flashing my application onto...
We have 2 different hardware designs which utilize the same peripheral connected to the nRF52833 via serial UART. They both use the same interrupt driven code to access the...
hi support team,
I was testing 7002dk with a Asus router,i found two questions:
1.5340tfm jump to application taks about 8 seconds, why it takes so much time?
2.7002dk...
Hi,
1.As shown in the following PSM eDRX figure, during the red period, how will the text messages sent to nRF9160 be processed? Will the nRF9160 module receive them in...
I have an external GPS module connected to an nrf9151dk over UART. The module is correctly powered, and sending messages over its tx pin, which has been confirmed by attaching...
I'm using the nRF52840 and Gazell Pairing (GZP) to develop a device network. Because I need bi-directional communication, I am not using GZP's encryption feature, as it does...
Hi,
I would like an nRFX example on how to set up DPPI using single in (1 Event) and multiple out (2 Tasks). I have previously done this using the fork functionality in...