Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi all
The nRF51822 product specification V3.2, chapter 8.8, specifies the times t_CSD and t_CC of the SPI slave peripheral for the low power mode and for the constant...
I've experienced some struggles programming for Taiyo Yuden's EYAGJNZXX board. According to the user manual provided its chip is nrf51822 (which supposedly works with s210...
Hello.
I have a question.
I use nrf52 & Keil.
I want to get data from sensors and send it with BLE.
Now, I found sample codes.
It uses UART and sends with BLE.
...
HI,
I want to send an "Echo" command to the nRF8001 using an ATMEGA328. Can some one suggest code for it ? How should the command be coded in a packet ?
Regards
Hey,
currently I use nrf_gpio_pins_set() and and nrf_gpio_pins_clear() from nrf_gpio.h to set and clear specific GPIO ports, respectively. If I want to change the current...
Alright, I have searched high and low and been unable to find a simple answer to this question. It must be possible for the nrf51 to launch Siri on an iPhone, I have seen...
Hi!
I'm doing an Arduino .txt file sending project using the nRF24L01+. But i'm quite a noob in this so i'd like a bit of advice.
I'm using an Arduino Uno, and I made...
Hello,
while reading some nrf5 examples, I've stumbled over a pattern in the examples, where the result code of a function is stored in variable (most of the time named err_code...
Hello Everyone,
I am porting rf receiver example code which are available in another platform.
I have used this rf module : www.amazon.in/.../B00NRQ3BIM
I am attach...
I am using app_timer to measure the time taken to execute a function. I am using ble_app_template code. As mentioned in the documentation, app_timer needs to initialize the...
I am developing an advertise only code.
There is PERIPHERAL_LINK_COUNT macro in ble_app_template that is used by the softdevice to reserve RAM for peripheral link...
I am using:
DK52
SDK 11
Softdevice S132 2.0.0
I have initialized my service as follows:
#define BLE_UUID_BASE_UUID {0x05, 0x00, 0x00, 0x00, 0x00, 0x00...
I migrate a project from keil to IAR, at the moment of bulding im facing this error:
arm_startup_nrf51.s
Error in command line: Invalid argument to option '-D'
Error...
We did initial work on the NRF51DK (PCA_10028).
We are using SDK 12 and ARM-GCC.
We were able to compile and run successfully the experimental_ble_app_blinky and connect...
I'm attempting to make a sense of app_gpiote.c (in SDK 11) to see if it's suitable for my application and I can't find a match between the documentation, the sample code and...
