Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hi, It's looks like I bricked my Thingy:91x . It was working fine when I program it with the target " thingy91x/nrf9151/ns " then later while learning I try program the in...
Hello,
I've got some questions regarding the use of DFU target library. I get my update data from the UART and like to use a setup with two partitions on my device. Is this...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi Nordic teams :
I find that datasheet v0.8 (page12) shows that SDA do not need clock.
Page 277 still shows that SDA need clock pin.
Could you help to clarify which...
Hi, I previously wrote about an unexpected behaviour which I've made a diagram for below. It's relatively simple though, the COMP watches a voltage and fires a toggle event...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Hi,
the nrf54L15 datasheet states on SPIM "CSN and DCX are not present in all configuration" (p.559). But I can't find the information, when CSN is available.
Hello, guys, I am working on distance measurement project using two nRF5340DK (nrf_dm sample application). I found duration for which the distance measurement between two...
Dear all,
1) I flash the code through the debugger to my pcb and it is running correctly (just on/off some LEDs).
2) I remove the JTAG+SWD connector, the project still...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
Dear Sirs,
I am writing you to inquire about following questions about nRF5340. We are using Laird BL5340 and SDK2.8.0 for our product.
The audio waveform during a wireless...
first i change to my kconfig file add this
source "samples/subsys/usb/common/Kconfig.sample_usbd"
source "Kconfig.zephyr
second I add to cmakelits
include...
