Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello,
I have an issue that I can't seem to sort out involving the PWM module. I am currently using SDK9.0 and SoftDevice S110 V8.0 and I am using the stock PWM files from...
I have a nRF51DK. And I would like to be able, to enable/disable the softdevice with 2 buttons.
Button 1 on nRF51DK --> Enable Softdevice
Button 2 on nRF51DK --> Disable...
Hello,
I am working on nRF51822 S110 softdevice 8.0 and SDK9.0. I am creating paired and unpaired states and the system will goto unpaired only if it is unpaired from the...
I know nrf51 timer0 can be configured for 16,8,24 and 32 bit modes
and timer1 and timer2 can be configured for 16 and 8 bit modes.
But what can I expect the value to be...
I'm going to star a new product development using nRF51422 supplied by a 3V battery. Since it is a low cost product the idea is to use the nRF51422 internal DCDC to provide...
Hello,
I'm using an external chip that decodes my RF transmission and outputs the data on two pins DAT, and CLK (data and clock). Currently I'm reading the data with GPIOTE...
We have written our own softdevice, but now we have a question about the stack pointer.
I read in the softdevice specification that the nordic softdevices share the stack...
I have been trying to establish a link that will feed sensor data into my com port via a Bluetooth uart bridge. I got my closest today by doing the following.
Load SDK10...
I'm having trouble making a single bank dfu mode with 128k NRF51822 chip.
Here's the problem;
Works fine when everything(SoftDevice, Application, Bootloader) is all...
Hi,
I am a newbie to Nordic BLE.
A make error occurs when building the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0 on my cross compile environment...
Good morning, i have windows 7 and at this moment i have installed "Gnu tools for ARM embedded Processors", "GnuWin32 ‐ GNU Make utility", "GnuWin32 ‐ Core Utility", "nrfgostudio...
Hello,
on our custom hardware design, the hardware reset won`t be executed after programming with nrfjprog.exe, until complete new boot with disconnecting Vcc.
After reconnecting...
We are going to use nRFgo - Bluetooth direct test mode to evaluate the nRF51 device RF performance, and we need to load the DTM (Direct test mode) application to the device...
