I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
I am using esb dpl in nrf5 sdk v11. I want to put a special packet in ack payload. but I think nrf_esb.c code can not do. the reason is that when on_radio_disabled_rx() is...
Hi,
I am developing a printed circuit board for myself using a NRF52 and I am unsure how to actually burn a bootloader program to the NRF52. Additionally, once the bootloader...
Hi All,
my device wakeup from system off casued from reset RWOFF, I read the register RESETSRC and byte E is 1.
maybe there is something about the configuration of gpio...
Hello,
I was reading about that 6LowPAN is being used in the IoT SDK.
I have a few questions about this.
Can the 6LoWPAN node communicate with another 6LoWPAN node...
Hi,
I am working nRF51822 communication. I am using nRF peripherals examples in SDK 11.0 series.
I would like to know the sleep mode examples in communication like after...
Hello,
I bought few nRF24L01+ modules and I integrated them in some custom PCBs that I designed.
I haven't been able to transmit information:
The TX FIFO is full...
I'm working on a very simple Gazell build - basically the gzll_ack_payload example with some of it pulled out, since I'm working on a board with no LEDs or buttons to run...
Hi,
I am trying to develop a PCB for the NRF52 that will use bluetooth capability. However, I was wondering if there were smaller antenna's that could be used rather than...
If I have Bluetooth earbuds, one set to master and the other a slave on my ears.
Is the communication between the ears, through the head, or around the head (Hair scalp...
Hi all
I have two questions/problems regarding the emulated System OFF mode with the NRF52832 and the SoftDevice S132 V2.0.1:
According to this thread , an infinite...
It is to my understanding that you DO have to worry about that when using keil download function or other means to program either the softdevice or your program to the nrf514xx...
hi,
I have created shared channel. currently I only have one master and one slave working.
Master is sending data to slave and it s working perfectly.
But I can not...
Hello,
i haven't found an answer to this question. Which address uses the PTX in Enhanced Shock Burst Protocol (nrf52832, SDK 11)? In the code I found only that:
NRF_RADIO...
Hi
According to the BT spec v4.2, Volume 6, section 4.5:-
"There shall be only one connection between two LE device addresses.
An initiator shall not send a connection...
As show in the title, suppose I have my own bluetooth stack implementation, Is there any possible to flash the bluetooth stack into the nordic series?
Or, another question...
