How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi guys,
I'm working on an nRF52832 chip (PCA 10040) with softdevice s132 (v3.0.0) and I'm facing with a big problem; in my project I use an spi (instance index 0) and an...
Hi,
we have the need to develop an application that needs a precise second counter over time.
Our firmware is using the S110 SoftDevice (v8.0.0) and SDK v8.0.0 to perform...
Hi!,
I'm trying to compile GitHub examples, for example this github.com/.../nrf51-ble-tutorial-service
I cloned it into nRF5_SDK_12.1.0_0d23e2a/examples/peripheral....
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
Hi
We are using "gcc compiler" to compiler our programs. To download our programs we use "nRFgo Studio" app.
From the above image, when we load SDK into the device...
Hello,
Consider this scenario:
The client successfully writes to a characteristic by the application code can't use the data sent so it would be usefull to signal the...
Hello,everyone. Now i have the board nrf52832 and i want it to enter the low-power mode but keep the the advertising. Now the measured current is 160uA, I think there should...
Dear All,
I apologize in advance if it seems that the question has been already posed but it is still unclear to me.
I have a pin (SIG_OK) and I want to read its logic value...
On the nRF51 DK there is a MM8130-2600 connector. I suppose it is used for connecting coax cable when tuning the antenna(?)
The connector is quite expensive, though. Is...
Per the name "UUID" and the very limited background knowledge that I have, it appears that a particular device can have its UUID assigned by its manaufacture, who bought the...
Hello.
I am developing a BLE application on NRF52832 using Nordic SDK11 and S132 softdevice. I use Linux PC as a BLE host device, and can pair & bond the NRF bluetooth...
Hi there! I'm using the nRF Toolbox's UART to test the receiving of my data stream. I'm trying to send a data array collected (from spi) in my main loop and send it via UART...
I am studying the iot-sdk of nordic.
Now, as I have shown in previous questions, I can not detect the device under the linux system according to the toturial in iot.
Now...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1?
About problem:
...
