But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello,
I have some trouble to use the Secure Bootloader example, which comes with the
nRF5_SDK_12.1.0
I installed the latest nrfutil and hexmerge. I can compile the...
This piece of code appears in all IoT SDK examples:
eui48_t ipv6_medium_eui48;
err_code = ipv6_medium_eui48_get(m_ipv6_medium.ipv6_medium_instance_id,
&ipv6_medium_eui48...
Hi, I am using the nrf uart app to communicate with a smart phone and the NRF52. I am trying to detect whenever it is sent a value between 0 and 60 from the phone, and save...
Hi,
I'm working on nRF51822 with SDK 11.0.0 softdevice s130
I have an nRF module acting as central and smartphones (iOS and Android) acting as peripheral.
I tested...
Hello, what is the BLE max range w/out usin PCB antenna?
And what range ll be if i reducing the connection interval down to the minimum 7.5ms, set Tx power to +4dBm using...
I am using the nrf51822-QFAC-R in an application where the realization of the antenna is very challenging, and I expect to have an antenna |S11|=-1dB, with variations of the...
Hello, I want to clear things up a bit, all these concepts are starting to overwhelm me somehow. I want to know:
What can have UUID and handle? I understand that profiles...
I want to use ATMEGA 328 to send a packet over to the chip as follows:
SPDR = packet ;
Can some one kindly post what the content of this packat should be ?
is it possible...
hi,
i am working on FDS. here i am able to write number of records and also able to read them back.
but while updating i deleted one of the old record and writing new...
Hello,
I have some problems with UART communication with my nRF51 DK.
When I connect it through USB cable, all is ok. But when I connect pins: P0.09(TXD), P0.11(RXD) to...
Hello, i have a question.
Can nRF51822(s120) handle more than one connection at same time?
Let me explain: i have one server(nRF51), and two(or more) clients(nRF51 and mobile...
I've got an application that does a lot of nRF51822 GPIO wiggling and the timing needs to be controlled. In one spot I simply set a pin high then low like this:
nrf_gpio_cfg_output...
As shown in title, I am using the ubuntu 14.04 in virtualbox.
When I connect the Nordic 51822 development kit to my PC, I can only detect the serial number of this device...
keil uvision
Hello. I don't know how to get away from the warning "last line of file ends without a newline".
I added new line, but nothing change. It happened with my own...
Dear Sir,
Here I would like to disable the Adversting idle power down dynamically but in some situation it will fail.
The APP_ADV_TIMEOUT_IN_SECONDS is 180 seconds as...
