After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello,
We have found a bug in nrf_bootloader that can prevent the application from starting up properly.
In nrf_bootloader_app_start.c, the nrf_bootloader_app_start()...
I saw the example of Andriod nRF Master Control/Connect app triggering the FOTA for mbed platform without using any button. Unfortunately, I don't have Andriod device and...
during the pcb design of nrf52, is it compulsory to totally copy your reference pcb layout . since our case need to design a small size device, so i have to modify the pcb...
Hi,
I wanted to know whether Bluetooth 5.0 will ever be supported on the NRF51 series chips or we need to migrate from NRF51 to NRF52 in order to have Bluetooth 5.0 in...
hi,I have a issue about pairing.
anyone can tell me the process of pairing and binding ,how the event BLE_GAP_EVT_SEC_PARAMS_REQUEST generate;
Do you have same example about...
Hello,
I am developing a board, with nrf51422-qfaa chip. To match the antenna I'm using the BAL-NRF01D3 balun. I currently have problems with antenna not working and I'm...
I am running an appliction with S132 soft device, build on top of SDK 12.0.0. Problem is that the application sometimes stops running for ten seconds, or even more, when Bluetooth...
Hi all,
may be you can advice me on a solution.
I need to be able to wake up a system when one of the pins shows more than 1v and I also need to wake up system when...
Hi,
I'm using ble_app_multilink_central to connect different device.In the example, it can connect to the lbs service. If I want it connect the uart service,such as ble_app_uart...
Hi Nordic,
we need to modify bootloader code base on your dfu example. Now We meet a problem that we can't program it by clicking icon "Load" on keil comile project. report...
I am having problem to download SDK NRF51 12.0 example firmware onto Redbearlab BLE Nano nrf51822. The compilation and build is fine. It is shown as
Erased Failed!
Error...
I have a custom board with an nRF51822, running the ble_app_hrs from the 12.1.0 SDK with softdevice s130, using the internal RC clock in a custom_board.h as follows:
#define...
I'm learning about the nRF52 series and so far love everything I see, especially the SDK. But I just got to the point where I'd like to generate precisely timed output, and...
Hello Nordic Team,
As I'm worrying about the max payload lengh that I can notify using soft device s130.1.0.0 on nrf51822 (256 Kb Flash/ 16KB RAM, SDK10), I thought about...
Hi,
I'm porting our project from sdk10 to sdk12 with SD S132 V3.0.0. I cannot find a way to reset the device in app and boot in bootloader in order to do a OTA update....
