Hi,
I am currently making an upgrade og a nRF51422 project that has both BLE. and ANT+ Cycling Power profiles and if I run the old project on an 51822 processor I can see...
Further into development of the ReRAM file system. I noticed that in generated DTS for nRF54L15 board for the ReRAM we have:
What is the reason for providing erase-block...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hi, I have two firmware images: A and B which I need to make compatible for OTA (DFU over BLE using MCUBoot - the standard process described in the devacademy course ). They...
Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
Hi! I am working on a project that uses the Multilink example. On the client (nRF51422 w. SD 120) my program crashes and starts the main loop again after a few seconds. I...
Hi,
I'm developing a device that will be powered by two AAA alkaline batteries.
Since the operating voltage of nRF51822 is 1.8 to 3.6V I was considering to connect them...
Hi,
the example ble_app_uart_s132 from the SDK 0.9.2 is not longer working with the new release of S132 ( s132_nrf52_2.0.0-7.alpha). I had to go back to s132_nrf52_1.0...
My setups are:
RBL BLE Nano
nRF51_SDK_9.0.0_2e23562
Keil uVision V4.74.0.22 or gcc-arm-none-eabi-4_8-2014q2-20140609-win32
My design is to advertise a manufacturer...
I'm using nRF51422 with SDK 9.0.0 and S310 ver 3.0.0.
First, I program softdevice and dual bank bootloader by nRFgoStudio. After that it is possible to program my application...
Hi all,
first of all thank you for such a great knowledge base and community exchange.
I am pretty new in the development for nrf51822 devices.
I managed to run the...
The comment above app_button_init says, in part:
* @note Normally initialization should be done using the APP_BUTTON_INIT() macro
This macro is also mentioned in the...
I'm using the s130 SoftDevice on the nRF51 dongle and writing a PC app in python. How can I declare an int8_t in python for use in the sd_ble_gap_rssi_get function? The function...
Hello there, I am already guessing that by the question alone it seems like what i'm asking is silly or wrong but I have no formal education here so I will need some help...
Hey guys,
I'm building a remote control (similar to TV remote) and I'm using nRF51. I am trying to figure out optimal connection parameters so the battery would last as...
I am using nRF51 SDK v10.0.0 and running simple_uart application on nRF51822 Evaluation Kit(PCA10001).
Added CFLAG += -DBOARD_PCA10001.
after flashing with nrfjprog...
The nrf51 was able to use the Gazelle protocol down to 250kbs, giving quite an improvement in sensitivity and range.
The nrf52 doesn't mention Gazelle, but does mention...
we'd like to have a closer look at nRF52832 , which seems to be a good choice for our next evaluation step of our wearable device.
But we see that only an "objective" datasheet...
Hi,
on aliexpress you can buy a nRF 51 board with a LIS3DH digital output motion sensor:
de.aliexpress.com/.../32325205949.html
Is there any example or source available...
Hello there,
Is there anyway I can program the chip without the PCA10036? I want to add the nRF52 in one PCB I am designing, but would also want to be able to program it...
