I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I had a PWM question ( here ). It was recommended that I install SDK 10 and use the PWM files from SDK 10. I installed and copied the PWM files from 10 to 9 and opened my...
Hi, I've compiled program from this link:
developer.mbed.org/.../
The problem is that I can't connect to my DK by nRF UART 2.0 app, probably because not every UUID is...
I am working on adding a timer in the ble_app_uart sample, aiming on disconnect with device which doesn't send any data in specific time, such as 5 seconds.
Now I have...
I get NRF_ERROR_SVC_HANDLER_MISSING error in spi_open function.
uint32_t err = sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type);
APP_ERROR_CHECK(err);
I'm using...
hi,
I need to store persistent data of about 32 bytes in flash, so tried using pstorage APIs (SDK v9.0 on nRF51822 -- 256KB ).
I followed the sample code given here...
Hello,
I am using keil uvision 5.17, sdk 9.0.0 and sd 130.
Once I programmed whole application through mbed,
Then I moved into keil and implemented all function....
We are trying to communicate to NRF51422 through PC using UART communication. But the programs works fine with nRF51822 Dongle and DK. But it does not works with another dongle...
Hi experts,
I need nrf51822 to send thousands of packets (notification) to Master Control Panel (PC), and expect for high data rate. So, I turned the connection interval...
if initial uart_config() before ble_stack_init(), softdevice_handler_init will be failed!
with SDK 6.0
softdevice_handler_init() will returns 0x00001001 ("NRF_ERROR_SDM_INCORRECT_INTERRUPT_CONFIGURATION...
I am trying to generate code using BDS and the Nordic Plugin 1.2 but I keep getting the following error. I have reviewed the XML but I can't seem to find the issue. Any thoughts...
I've been fighting this bug for a few days now and I thought I'd share what I discovered in the process.
I wanted to set up a couple PWM channels to control a few LEDs...
getting problem in implementing uart. code is here
#include <stdio.h>
#include "boards.h"
#include "app_util_platform.h"
#include "app_uart.h"
#include "app_error.h...
I implemented measuring of Lithium battery level with the help of thread How to measure Lithium battery voltage . I am using nRF51422 with SoftDevice 110 and SDK 9.0.0 and...
