after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello All,
I have modifies the Spi Master code to communicate with an ADXL345 Accelerometer. I set up my powermode and the percesion in the setup phase. However, when I send...
Hello, Nordic Team.
In my program, I have to change the value of the characteristic before start. I write:
case ACI_EVT_DEVICE_STARTED:
g_aci_state.data_credit_total...
Hello,
I want to make my Arduino coupled with the nrf8001 advertising a simple data (an integer). There should also be a possibility for dynamically changing the advertising...
I have a Jayconsystems breakout board for the nrf8002 bluetooth chip. Nothing is connected to the breakout board and the chip is unprogrammed. My current meter reads 6.0 mA...
The nRF8001 Product Spec says,
"Dynamic Window Limiting reduces the average current consumption by reducing the window widening of the receiver ... Enabling this feature...
Hello,
I am trying to play alarm in button click using nrf code. I am using Nordic nRF51822 device and trying to integrate with android device. When I am using linkloss then...
Hey guys,
Working with the simple be_app_beacon example on nRF51. I’d like to be able to stop and start advertising. But after stopping advertising, I’m unable to start...
Hi，
Can the examples in <keil_location>ARM\Pack\NordicSemiconductor\nRF_Examples\9.0.0 of PCA10028(nRF51422 chips) be use on nRF51822 chips? Or how to modify it to adapt...
Hi
in my application I use about 8 app_timer instantiations (so 8 x app_timer_create), with various frequencies.
I noticed now that one timeout handler is triggered twice...
any body know about android code for pairing with ble (nrf51dk)?
please help i want to pair my android app to the chip. app is discovering the chip but not able to connect...
Hi
nrf 52832 is able to run in 64 MHz using external 32 MHz crystal.
I wondered if I can use an external 16 MHz crystal, and get the CPU to run in 32 Mhz.
Thanks
...
Hi, All
sdk v7.2, IOS 9.1
I know after peering with IRK, iOS will connect 51822 actively.
There're some issue in my project. It's not certain happen.
At most of...
I developed an application program and I have a hex file generated from mbed compiler, and would like to know if I flash this hex file using a J-link interface on NRF51822...
