Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I want to add an external PA to the NRF51422. My understanding of 15.247 is that you can transmit up to 30dBm if you use spread spectrum. Does the NRF51422 use DSSS for Bluetooth...
When is the most appropriate time to set the transmit power while using the S120 softdevice? I want to set it once at power up. Most examples that use the S110 SD set the...
Suppose I want my BT peripheral to provide Measured value of sensor X and Location of sensor.
Currently I have to send the following attributes
Service Attrinbute
Characteristic...
Hi All,
I am working a custom board for 51822. We have wired the UART RX/TX pins to a microusb connector (No RXD/TXD pins wired). The problem is once we connect it to PC...
Hello,
all was working fine, until today.
When I plug my dongle, my computer does not react.
The green light on the dongle is off.
Even if I suppose that it's a...
For my current project, I need to compile the »over the air bootloader« with gcc (because our buildserver runs on linux, developers using Mac … no Windows and no Keil so far...
Hello, I want to get Pwm output using softdevice but i am not getting it.Here is my code attached main.c please tell me where i am going wrong.Do ineed to initialize softdevice...
I am looking at using the nRF51822 in an application to create an Ethernet gateway and want to be able to download new firmware to the nRF51822 from a remote server. I plan...
I have an nRF51822 application using the Soft Device 110. I want to perform bonding with a central without MITM protection. In my on_ble_evt() event handler, when the event...
Hi,
I am new to the scene of BLE beacon development. I am using multiple Bluetooth smart beacon kits for indoor ranging/positioning purposes. To reduce the effect of interference...
Hi,
For S110 6.0.0 we use such script to split hex to binary. But it seems 7.0.0 is changed and current way is not working anymore.
Convert from hex to binary. Split...
Hi
I am writing my own bonding manager.
In the S110 stack after Phase 3 of pairing the keys are exchanged which result in the EVT_AUTH_STATUS event which in turn contains...
when I add my own service and add characteristic, a odd phenomenon confuse me.
When I set cccd_md.write_perm:
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm);
...
after several attempts to debug and understand what goes in my handlers in the BLE callbacks, I thought to give a UART logger a try.
this is what I'm trying to use: OpenLog...
