Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I am facing an issue with the nordic 51822. I am declaring a gpio as output. I am writing logic High to that pin. When I check the signal in logic analyzer and multimeter...
Using rev 0218 firmware I am getting an awful lot of device errors with the mbed kit. I am not sure if this is a Nordic or an mbed issue so am asking in both places. Symptoms...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
I'm testing SPIM of nRF52 on PCA10040 using S132 and SDK11.
Its base on the app_peripheral_uart example, so I already have BLE communication.
When SPI is not initiated...
I have just received a nRF52 DK board and I am as a start trying to compile the associated Blink program in Keil 5.18 Lite. When I copy the blink example using the Pack Installer...
hi,
I was reading documentation and forum but failed to get a clear picture how AES module work.
So far my understanding is:
There are two ways to access AES either...
I'm building a product that can use the features from your Smart Remote 3. Is there someway to get the reference source files so I can adapt some of the smart remote features...
Hi,
Few days ago I received my DK-52, I set up the development environment based on Keil and started to compile some of the examples included into the SDK. I have not a Windows...
I have been googleing for a solution but have not found any solution yet.
Have tried the following:
Installed J-Link commander. (Does not pick up any usb devices...
We are a newbie team developing some measurement tests with the nRF52832 DK in order to evaluate the BLE from nRF52832 QFAA80 (s132 and pca10040) for IoT applications.
...
hi all,
Question:
i want to print "BUTTON IS PRESSED" continuously when button is pressed and i want to print "BUTTON IS RELEASED" when button is released.
eg: if i...
Now，I use a 1s timer to calculate the clock.
At first,I use the telephone to adjust the time to fit the telephone time.
but finally(after a night ) the result runs fastly...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I'm trying to get a UART example running on the nRF51822 mbed kit. However, flashing any uart examples from the SDK onto the board generates a fail.txt file
What is the...
Hi, i build my own custom board with a NRF52832, i'm having problem with the softdevice (i think so)... my code is base on BLE s132 central and peripheral...
I developed...
