There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
I managed to enable pairing without bonding on ble_app_uart by porting peer manager over from ble_app_gls. I am using SDK11 s130 on nRF51-dk.
I observed some strange behavior...
Hi Nordic's community,
I have an issue when writing uint32_t to a characteristic, i don't understand when i write uint16_t or uin8_t, it works ! but don't when i send an...
Hi,
I would like to add single bank signed DFU support to my project (running on nrf51822AC - 256kb version).
In SDK 10, there was an experimental bootloader with a nice...
Hi,
I want to transmit adv. data AES encrypted everytime. The Basic requirement is to do Encryption with Stream Cipher (Counter Mode) so i want to know when and where to...
Hi,
I am trying to get bonding to work in both iOS and Android versions.
As per the suggestion in : devzone.nordicsemi.com/.../ I used
attr_md.read_perm.sm=1;
attr_md...
I wanted to do pairing without bonding with ble_app_gls s130 SDK_11. I tried setting SEC_PARAM_BOND to 0. However, this caused the device to stop advertising. What is a better...
Hello ! Can I read with SPI registers without any problems from inside a ble_event_handler or a timer_handler or should I expect to have problems due to interrupt priorities...
In the SPIM section of the product spec for the nRF52832, the spec describes sending the STOP task (even if the peripheral is already stopped) and receiving the STOPPED event...
Hi,
If I have a custom board with the NRF51822 operating at VDD=2.4V, would it be possible to program the part using Segger JLINK Lite programmer that comes with the dev...
I am attempting to update the firmware on a DFU V1 device using javascript inside of a cordova app. Due to the time it takes to roundtrip the write response it is going to...
Hello again,
Edit:
I am now only getting these 4 errors after enabling the clock in the nrf_drv_config.h file
I may be able to track down the problem myself if someone...
Hi,
I'm trying to get NFC working on a PCA10040 dev board. Using the nfc/record_url hex file it works fine, so the hardware is obviously ok.
However, when I use the...
I need to save data to flash on an nRF51422. I already have same basic thing working on an nRF52, so I figured the same API calls would work, but they don't. My main symptom...
I have an application that bonds to mobile devices and encrypts the connection on both Android and iOS. What I am noticing though, is that after each time I use the DFU to...
