Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi everyone,
I'm currently working on measuring the power consumption of the 9160DK board and following the guide: Getting started with current measurements on the nRF9160...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi
I connected RF Connect for Desktop to "nRF54L15_DK" in my Desktop
when I want to use Direct Test Mode,press Start test bottom,the log show "DTM setup reset command...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
Hello Sir,
I am currently working with the boards:52840dk and ncs:2.9.1
Regarding the issue of failed mcuboot upgrade after writing the upgrade firmware using flash APIs...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I am studying Lesson 6/wifi fund_1ess6uexer2 and I can run the provided code normally.
（academy.nordicsemi.com/.../） But I still want to control whether to send packets...
I have this main code:
With this overlay:
and this configuration:
I am using a nrf52840 dev board and have connected P0.06 and P0.08.
Why does it not trigger...
I'm playing a bit with MCU boot and folowed the tuturial . When I compile the sample with mcuboot from Zephyr, it works fine for the 52840DK, but when I try to compile for...
NPM2100 EK CONNECTION
Can I connect The NPM2100 EK with NRF52 DK? If so..... 1. How do I physically do this? 2. Can I program the NPM2100 EK to send Voltage Supply of 1...
When using Bluetooth AOA, I configured only two antennas to collect IQ data. Below are the curves formed by the 37 IQ data points collected from the two antennas during the...
Hello everyone,
I would like to learn how to create unit tests using the ZTest framework for a Nordic sample project, in order to better understand how it works.
I am...
Dear Nordic Teams :
I find the NFC current and find the current is quite large in the datasheet version 0.8. The value is much bigger than nRF52840. Is it correct?
Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
