Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I'm getting problems on the pca10001 uart example. I get the "Start:" string on the terminal but it can't echo what I type on the keyboard. Another thing is that I...
The nrf51 powerdown examples
github.com/.../nrf51-powerdown-examples.git
Are these power down examples are helpful. They clearly indicate how to power on the nrf51822...
I have a custom board using the nRF51822 as a peripheral with the S110 SoftDevice. The centrals are mobile apps, both Android and iOS. The device spends a lot of time in a...
Hi
I'm trying to run uart example on nrf6310.
I followed following link.
devzone.nordicsemi.com/.../
and I defined ENABLE_LOOPBACK_TEST.
it was resulted in blinking...
I am using sd 7.0.0, I have a simple bootloader implementation that follows the bootloader sample code pretty closely. When I jump to my application from the bootloader and...
Is there anyway to get a light to blink using only the PCB antenna module?
Also, is there anyway to blink a light using only the Bluetooth Smart Beacon chip?
Hi,
I'm attempting to use 'S120/experimental/ble_app_multilink_central' running on a pca10001 to better understand the central / peripherial comm sequencing on the nrf51...
Is there documentation missing from the SDK 6.0 docs (and 5.2) ?
For instance:
https://devzone.nordicsemi.com/documentation/nrf51/6.0.0/s110/html/a00125.html
is blank...
Hi All,
I am new to BLE nRF 51822 development kit. It is mounted on nRF go Starter Kit. My question is how can I put a advertising 51822 chip to sleep? Also, when I turn...
Hi
In my custom project I'm using pins P0.14 as SCL and P0.15 as SDA .
I know the pins selection #define is in twi_master_config.h. But the question is whether I have...
Hello,
I'm using: nRF51422-QFAA E00 and SDK - nRF51 5.2.0
Right now I'm running without softdevice enabled. I'm trying to use RTC1 Timer for my own delay_ms() function...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I am currently using s120 to create a central device to scan for my peripherals. In addition I am trying to parse the Advertising Report data and send it via UART.
p_ble_evt...
I have use PAC10000 and RF51822 EVB ,when i run sniffer.exe,and I found nrf51822 ble,[0],
select "w " and show " Starting Wireshark",but always show " Starting Wireshark...
Hi All,
I need the slave node(S110) send advertising continuously and monitored by master node, so I set the advertising parameters as:
adv_params.type = BLE_GAP_ADV_TYPE_ADV_NONCONN_IND;...
