Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
(mp3 or wav file) --> sd_card --> nrf51822 --> smart phone
Read the data from the SD_CARD transfers to smartphone.
void BLE_SEND_VOICE(void)
{
f_mount(0,&fs);
...
I've not worked with BT4.0/4.1 before, so I was wondering about this:
Take the heart rate monitor example, connection happens automatically when a heart rate monitor is discovered...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
I'm interested in using the chip and a very simple board. No buttons, no humidity or motion sensors, just the beacon (like a heartbeat). I'm trying to keep the price down...
Hi all,
I am using the experimental_ble_app_multiactivity_beacon example with S110 v7.1 and SDK 7.2. In particular the hrs_scanner app on the pca10028 board.
I am using...
Hi, I would just like to know if there's an equivalent to "BLE_GAP_EVT_CONNECTED" for services discovered. There's some stored data I want to send in a loop only after services...
Hi,
Does the nRF51822 have a capability of responding to multiple phones?
I am working with RFduino using the RFD22301. I'm assuming that the RFD22301 is the same BLE...
Hey,
the nRFgo Studio contains a simulator for the nRF8001 and 8002. Will there be an update in the near future to simulate the bahaviour of the nRF51 platform?
Mar...
I have TIMER2 running at 500us interval. ANT is working as 100Hz master.
Understood softdevice will affect the timing and cause some latency.
I am guessing it is delaying...
Hi:
I'm implementing an controller for an open source drone Crazyflie ( www.bitcraze.se/.../) . My device is similar to pca10001 board.
Since Crazyflie is acting as peripheral...
Hi all!
I've been unsuccessfully trying to DFU the Smart Beacon Kit with the latest firmware.
Using the nRF51 DK and the TC2030 tag connect cable I was able to program...
I am trying to get a communication between two pieces nRF51822 using the my service. I checked the peripheral with Master Controll Panel app and is working fine. The multilink...
Hi,
I have the (IoT) environment running. The Raspberry Pi (with Miredo tunnel) is connected to the outside world. I can ping6 the ipv6.google.com server from Rasperry...
Hi Team,
I am using nrf-51 DK as sniffer.
I need some guidance regarding how to study or analyze these packets?
I don't know what exactly I should check in each REQ...
