I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
I want to send images to my arduino from an app to nrf8001 and then display it on my device. Is nrf8001 made to only work in 20-byte wide receive buffer? Can it receive more...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hello all,
after a long period of trial and error I come for advice. I use the NRF24L01+ module with a slightly modified NRF24-library based on the work of MikeM ( www...
Hello,
I've recently bought a nRF905 development kit. From the nDP soft, i cannot detect my nrf905 EVBOARD.
The following driver is installed : "nRF2401 FS USB DEMO...
Good morning,
I just finished my circuit with nrf8001 + balun/antenna.
What is the process to have it review by Nordic?
Sorry for this question, I'm pretty new to PCB...
Hi
I would like to develop an application for the nrf51822 with a static passkey that connects with linux. The example "nRF51-ble-app-uart-static-passkey" gives a great...
Hi,
I would like to use Random number generator when soft device enabled. I have seen random generator example, but I can not use the same when soft device is enabled....
I was considering the following possibility, using an nrf51882 module or another module to receive ble advertisements. I'm pretty sure this is possible. Using the internel...
please, help me ㅠ_ㅠ
it mades me crazy
My PC is Windows 8.1 & 64 bit.
I try to install / repair / change SDK (6.1.0 version, 6.0.0 version, 4.4.1 version)...
I have achieved the demo referring to the IoT SDK and can control the lights on the nRF51 DK through the Firefox browser with Copper plgu-in in the LAN.Recently I want to...
Hi,
I interested in a simple system of a master and slave nrf2460. But how many of these systems would happily coexist in a the same room?
Thanks
Senthil
The Enhanced ShockBurst PTX Project just inits the ESB and start transmitting without ever configing either of the 16MHz or 32kHz clocks (none that I can see at least).
...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
hi.I have a question about synchronization. In main loop, there is a function sd_app_event_wait() which blocks until ble event from softdevice call occurs, so I want to put...
